Transmission Diagnosis - With Codes
- Application
- Identification
- Description
- Operation
- Component Locations
- Programming
- Trouble Shooting
- Performance Tests
- Self-Diagnostic System
- Diagnostic Tests
- Fault Code 01: Transmission Relay Control (Relay Sticks, Short Circuit)/Solenoid Valves Power Supply Relay Sticking Open Or Short Circuit
- Fault Code 02: Transmission Relay Control (Relay Sticks, Open Circuit)/Solenoid Valves Power Supply Relay Sticking Closed Or Open Circuit
- Fault Code 03: EEPROM Communication Fault/Ecu Fault, EEPROM Communication
- Fault Code 04: EEPROM Checksum Fault/Ecu EEPROM Checksum
- Fault Code 05: Torque Converter Lock-Up Clutch Monitoring/Torque Converter Lock-Up Clutch Fault
- Fault Code 06: Watchdog Check, Ecu Fault
- Fault Code 07: Solenoid Valve Lockup Clutch Check (Short Circuit To Voltage)/Torque Converter Lock-Up Solenoid (MV3) Short Circuit
- Fault Code 08: Solenoid Valve 1 Check (Short Circuit To Voltage)/Shift Solenoid (MV1) Short Circuit
- Fault Code 09: Solenoid Valve 2 Check (Short Circuit To Voltage)/Shift Solenoid (MV2) Short Circuit
- Fault Code 10: Pressure Regulator Check (Short Circuit To Voltage)/Pressure Regulating Solenoid (MV4) Short Circuit
- Fault Code 11: Can Message MD-REIB Invalid (FFH)/Can Message: Engine Friction Invalid
- Fault Code 12: MES Line 1 Fault/BECM To Message Center Circuit Fault
- Fault Code 13: MES Line 2 Fault/BECM To Message Center Circuit Fault
- Fault Code 14: Position Switch Monitoring (Permanent)/Gear Position Switch Incorrect Outputs
- Fault Code 15: Can Level Monitoring
- Fault Code 16: Can Bus Monitoring/Can Bus Fault
- Fault Code 17: Can Time-Out Monitoring
- Fault Code 18: Can Message WFPDK (Throttle Angle) In Invalid (FFH)/Can Message: Throttle Position Invalid
- Fault Code 19: Can Message T-Mot Invalid (FFH)/Can Message: Engine Temperature Invalid
- Fault Code 20: Can Message V3 (Road Speed) Invalid (FFH)/Can Message: Road Speed Invalid
- Fault Code 21: Downshift Safety Monitoring/Downshift Safety Monitor Prevented Downshift Which Would Have Caused Engine OVERSPEED
- Fault Code 22: Stall Speed Monitoring/Torque Converter Slipping
- Fault Code 23: Position Switch During Cranking/Gear Position Switch Incorrect Outputs
- Fault Code 24: Battery Supply Check/Battery Supply Below 9 Volts While Engine Is Running
- Fault Code 25: Solenoid Valve For TC (Short Circuit To Ground, Or Open Circuit)/Torque Converter Lock-Up Solenoid (MV3) Open Circuit
- Fault Code 26: Solenoid Valve 1 (Line Short Circuit Ground, Or Open Circuit)/Shift Solenoid (MV1) Open Circuit
- Fault Code 27: Solenoid Valve 2 (Line Short Circuit Ground, Or Open Circuit)/Shift Solenoid (MV2) Open Circuit
- Fault Code 28: Pressure Regulator (Line Short Circuit To Ground, Or Open Circuit)/Pressure Regulating Solenoid (MV4) Open Circuit
- Fault Code 29: Gear Ratio Monitoring, 1ST Gear/Ratio Monitoring Implausible 1ST Gear Ratio
- Fault Code 30: Gear Ratio Monitoring, 2ND Gear/Ratio Monitoring Implausible 2ND Gear Ratio
- Fault Code 31: Gear Ratio Monitoring, 3RD Gear/Ratio Monitoring Implausible 3RD Gear Ratio
- Fault Code 32: Gear Ratio Monitoring, 4TH Gear/Ratio Monitoring Implausible 4TH Gear Ratio
- Fault Code 33: Can Message MD-Ind Invalid, Indicated By F-TL-MES/Can Message: Engine Torque Invalid
- Fault Code 34: Can Message MD-Ind Invalid (FFH)/Can Message: Engine Torque Invalid
- Fault Code 35: Can Message N-Mot Invalid, Indicated By F-N-Mot/Can Message: Engine Speed Invalid
- Fault Code 36: Transmission Calibration Selection Incorrect/Invalid
- Fault Code 37: Can Message T-Ans Invalid (FFH)/Can Message: Engine Air Intake Temperature Invalid
- Fault Code 38: Can Message FHOEHE Invalid (FFH)/Can Message: Altitude Shift Control Invalid
- Fault Code 39: Range Switch Plausibility Error/Transmission High/Low Range Implausible Input
- Special Tools
- Connector Identification
- Wiring Diagrams