Engine Mechanical - 2.2L
- Specifications
- Fastener Tightening Specifications (2.2L)
- Engine Mechanical Specifications (2.2L)
- Adhesives, Fluids, Lubricants, and Sealers
- Thread Repair Specifications
- Engine Block - Front View
- Engine Block - Back View
- Engine Block - Left Side View
- Engine Block - Bottom View
- Engine Block - Right Side View
- Engine Block - Top View
- Lower Crankcase - Front View
- Lower Crankcase - Back View
- Lower Crankcase - Bottom View
- Lower Crankcase - Left View
- Lower Crankcase - Right View
- Cylinder Head - Top View
- Cylinder Head - Intake Manifold Deck View
- Cylinder Head - Exhaust Manifold Deck View
- Cylinder Head - Front View
- Cylinder Head - Back View
- Component Locator
- Diagnostic Information and Procedures
- Diagnostic Starting Point - Engine Mechanical
- Symptoms - Engine Mechanical
- Base Engine Misfire without Internal Engine Noises
- Base Engine Misfire with Abnormal Internal Lower Engine Noises
- Base Engine Misfire with Abnormal Valve Train Noise
- Base Engine Misfire with Coolant Consumption
- Base Engine Misfire with Excessive Oil Consumption
- Engine Noise on Start-Up, but Only Lasting a Few Seconds
- Upper Engine Noise, Regardless of Engine Speed
- Lower Engine Noise, Regardless of Engine Speed
- Engine Noise Under Load
- Engine Will Not Crank - Crankshaft Will Not Rotate
- Coolant in Combustion Chamber
- Coolant in Engine Oil
- Engine Compression Test
- Cylinder Leakage Test
- Oil Consumption Diagnosis
- Oil Pressure Diagnosis and Testing
- Oil Leak Diagnosis
- Crankcase Ventilation System Inspection/Diagnosis
- Drive Belt Chirping, Squeal, and Whine Diagnosis
- Drive Belt Rumbling and Vibration Diagnosis
- Drive Belt Falls Off and Excessive Wear Diagnosis
- Drive Belt Tensioner Diagnosis
- Repair Instructions - On Vehicle
- Intake Manifold Cover Replacement
- Drive Belt Replacement
- Drive Belt Tensioner Replacement
- Engine Oil Pressure Switch Replacement
- Engine Mount Inspection
- Engine Mount Bracket Replacement
- Engine and Transmission Mount Balancing - All Mounts
- Powertrain Mount Balance - Lower Mount
- Engine Mount Replacement
- Engine Support Fixture
- Oil Level Indicator Tube Replacement
- Positive Crankcase Ventilation Hose/Pipe/Tube Replacement
- Intake Manifold Replacement
- Crankshaft Balancer Replacement
- Crankshaft Front Oil Seal Replacement
- Engine Front Cover Replacement
- Camshaft Timing Chain, Sprocket, and Tensioner Replacement
- Camshaft Cover Replacement
- Timing Chain Tensioner Replacement
- Intake Camshaft and Valve Lifter Replacement
- Exhaust Camshaft and Valve Lifter Replacement
- Camshaft Position Intake Actuator Replacement
- Camshaft Position Exhaust Actuator Replacement
- Valve Stem Oil Seal and Valve Spring Replacement
- Cylinder Head Replacement
- Oil Pan Replacement
- Piston, Connecting Rod, and Bearing Replacement
- Cylinder Sleeve Replacement
- Engine Flywheel Replacement
- Crankshaft Rear Oil Seal Replacement
- Engine Replacement
- Engine Oil and Oil Filter Replacement
- Repair Instructions - Off Vehicle
- Draining Fluids and Oil Filter Removal
- Crankshaft Balancer Removal
- Engine Flywheel Removal
- Oil Level Indicator and Tube Removal
- Exhaust Manifold Removal
- Intake Manifold Removal
- Camshaft Cover Removal
- Engine Front Cover and Oil Pump Removal
- Timing Chain and Tensioner Removal
- Intake Camshaft, Bearing Cap, and Lash Adjuster Removal
- Exhaust Camshaft, Bearing Cap, and Lash Adjuster Removal
- Water Pump and Balance Shaft Chain and Tensioner Removal
- Balance Shaft Removal
- Water Pump Removal
- Cylinder Head Removal
- Oil Pan Removal
- Piston, Connecting Rod, and Bearing Removal
- Lower Crankcase Removal
- Crankshaft and Bearing Removal
- Engine Block Disassemble
- Engine Block Cleaning and Inspection
- Cylinder Honing
- Cylinder Sleeve Removal (2.2L)
- Cylinder Sleeve Installation (2.2L)
- Crankshaft Balancer Cleaning and Inspection
- Engine Flywheel Cleaning and Inspection
- Crankshaft and Bearing Cleaning and Inspection
- Piston and Connecting Rod Disassemble
- Piston, Connecting Rod, and Bearing Cleaning and Inspection
- Piston and Connecting Rod Assemble
- Camshaft Cleaning and Inspection
- Camshaft Timing Chain and Sprocket Cleaning and Inspection
- Balance Shaft Cleaning and Inspection
- Water Pump and Balance Shaft Chain and Sprocket Cleaning and Inspection
- Cylinder Head Disassemble
- Cylinder Head Cleaning and Inspection
- Cylinder Head Assemble
- Oil Pump Disassemble
- Oil Pump Assemble
- Intake Manifold Cleaning and Inspection
- Exhaust Manifold Cleaning and Inspection
- Oil Pan Cleaning and Inspection
- Thread Repair
- Service Prior to Assembly
- Engine Block Assemble (2.2L)
- Crankshaft and Bearing Installation
- Lower Crankcase Installation
- Crankshaft Rear Oil Seal Installation
- Piston, Connecting Rod, and Bearing Installation (2.2L)
- Cylinder Head Installation
- Intake Camshaft, Bearing Cap, and Lash Adjuster Installation
- Exhaust Camshaft, Bearing Cap, and Lash Adjuster Installation
- Balance Shaft Installation
- Water Pump Installation
- Balance Shaft to Engine Timing
- Water Pump and Balance Shaft Chain and Tensioner Installation
- Camshaft Timing Chain, Sprocket, and Tensioner Installation
- Crankshaft Front Oil Seal Installation
- Engine Front Cover and Oil Pump Installation
- Oil Pan Installation
- Crankshaft Balancer Installation
- Camshaft Cover Installation
- Oil Filter with Cap and Seal Installation
- Intake Manifold Installation
- Exhaust Manifold Installation
- Oil Level Indicator and Tube Installation
- Engine Flywheel Installation
- Engine Prelubing
- Description and Operation
- Special Tools and Equipment