2.5L Turbo CEC Testing
- Testing & Diagnosis
- System Diagnosis
- Preliminary Checks
- Diagnostic Procedure
- Entering On-Board Diagnostics
- Check Engine Light Diagnostic Mode
- DRB-II Diagnostic Mode
- DRB-II Switch Test Mode
- DRB-II Read Input States
- DRB-II Read Output States
- DRB-II Actuate Solenoids & Relays
- DRB-II Actuate Outputs
- DRB-II Read Sensor Voltages
- DRB-II Read Sensor Values
- DRB-II Set Engine RPM
- DRB-II Minimum Airflow Speed
- DRB-II Emissions EMR Tests
- DRB-II Read Module Information
- DRB-II Problems & Error Messages
- Clearing Codes
- Emission Maintenance Reminder (EMR) Light Reset Procedure
- Emission Maintenance Reminder (EMR) Mileage Transfer
- DTC Identification
- No Start Test Information
- Notes
- No Start Test Information
- NS1 - Spark, Fuel Control, & Fault "Ignition Control CKT"
- NS2 - Fuel Pressure, TPS & Power Supply (Z1) To Injectors
- NS3 - Checking SMEC, Fuel Fouled Plugs & Engine Timing
- NS4 - Bad SMEC, Fuel Pump & CKTS, & Restricted Fuel Lines
- NS5 - Power Supply To Coil Primary & Primary Control CKTS
- NS6 - Spark Control Circuitry
- NS7 - Fault Messages "INJ 1 & INJ 2 Peak Current"
- NS8 - Faults "INJ 1 & INJ 2 Control Circuit"
- NS9 - Checking For System Faults
- NS10 - System Power & Ground, Shorted Map, Bad SMEC & Defective Distributor Pick-Up
- NS11 - Distributor Pick-Up & Connecting Circuits
- NS12 - ASD Relay Fault & Pull-In Coil Circuits
- NS13 - Fault Message "Z1 Voltage Sense"
- NS14 - Fault Message "FJ2 Voltage Sense"
- NS15 - Distributor Sync Pick-Up, CKTS To Pick-Up & Bad SMEC
- NSVER - No Start Verification
- DRIVEABILITY Tests
- DRIVEABILITY Test Information
- Dr1 - Checking System For Faults
- Dr2 - Checking SMEC Controlled Components
- Dr3 - Intermittent Test For Solenoids & Relays
- Dr4 - Intermittent Test For Map Sensor Signal
- Dr5 - Intermittent Test For Sensor Voltages
- Dr6 - Intermittent Test For Injectors & AIS Motor
- Dr7 - Checking For Fault Message "Map Pneumatic Signal"
- Dr8 - Checking For Fault Message "Map Pneumatic Change"
- Dr9 - Checking For Fault Message "Map Voltage Too Low"
- Dr10 - Checking For Fault Message "Map Voltage Too High"
- Dr11 - Checking For Fault Message "Vehicle Speed Signal"
- Dr12 - Checking For Fault Message "Oxygen Sensor Signal"
- Dr13 - Checking For Fault Message "Coolant Voltage Low"
- Dr14 - Checking For Fault Message "Coolant Voltage High"
- Dr15 - Checking For Fault Message "TPS Voltage Low"
- Dr16 - Checking For Fault Message "TPS Voltage High"
- Dr17 - Checking For Fault Message "AIS Motor Circuits"
- Dr18 - Checking For Fault Message "Purge Solenoid Circuit"
- Dr19 - Checking For Fault Message "EGR Solenoid Circuit"
- Dr20 - Checking For Fault Message "EGR System Failure"
- Dr21 - Checking For Fault Message "A/C Clutch Relay CKT"
- Dr22 - Checking A/C Condenser Fan Operation
- Dr23 - Checking For Fault Message "Radiator Fan Relay"
- Dr24 - Checking For Fault Message "WASTEGATE Solenoid"
- Dr25 - Checking For Fault Message "FJ2 Voltage Sense"
- Dr26 - Checking For Fault Message "Boost Limit Exceeded"
- Dr27 - Checking For Fault Message "Barometric Read Solenoid"
- Dr28 - Check For Fault Messages "EMR Mileage ACCUM" & "EEPROM Write Denied"
- Dr29 - Checking Sensor Calibrations (Begin With Cold Engine)
- Dr30 - Spark Plug Check
- Dr31 - Checking Sensor Calibrations (Begin With Warm Engine)
- Dr32 - Checking Secondary Ignition System
- Dr33 - Checking Basic Timing & Fuel System
- Dr34 - Checking Oxygen Sensor Operation
- Dr35 - Checking Throttle Body Minimum Airflow
- Other Possible Causes Of DRIVEABILITY Related Problems
- DRIVEABILITY Verification Test Information
- Speed Control Test Information
- Charging System Test Information
- Charging System Test Information
- Ch1 - Checking Charging System For Fault Codes
- Ch2 - Checking For Fault Code 16 "Battery Input Sense"
- Ch3 - Checking For Fault Code 46 "Battery Voltage High"
- Ch4 - Checking For Fault Code 47 "Battery Voltage Low"
- Ch5 - Checking For Intermittent Fault Codes
- Ch6 - Checking Charging System With No Fault Codes
- Wiring Diagrams
- Removal & Installation