Data Monitor Mode

NOTE:

The following table includes information (items) inapplicable to this vehicle. For information (items) applicable to this vehicle, refer to CONSULT display items.
For reference values of the following items, Refer to Physical Values .

Monitored Item

Monitored item	Unit	Description	Remarks
COOLANT TEMP/S	deg.C	The engine coolant temperature (determined by the signal voltage of the engine outlet coolant temperature sensor) is displayed.	When the engine coolant temperature sensor is open or short-circuited, ECM enters fail-safe mode. The engine coolant temperature determined by the ECM is displayed.
VHCL SPEED SE	km/h or mph	The vehicle speed computed from the vehicle speed signal sent from combination meter is displayed.
BATTERY VOLT	V	The power supply voltage of ECM is displayed.
INT/A TEMP SE	deg.C or deg.F	The intake air temperature (determined by the signal voltage of the intake air temperature sensor) is indicated.
PURG VOL C/V	%	Indicates the control value of the EVAP canister purge volume control solenoid valve computed by the ECM according to the input signals. The opening becomes larger as the value increases.
FUEL T/TMP SE	deg.C or deg.F	The fuel temperature (determined by the signal voltage of the fuel tank temperature sensor) is displayed.
FUEL LEVEL SE	V	The signal voltage of the fuel level sensor is displayed.
EVAP SYS PRES	V	The signal voltage of EVAP control system pressure sensor is displayed.
CAL/LD VALUE	%	"Calculated load value" indicates the value of the current air flow divided by peak air flow.
HO2S2 (B1)	V	The signal voltage of the heated oxygen sensor 2 is displayed.
ENG OIL TEMP	deg.C deg.F	The engine oil temperature (determined by the signal voltage of the engine oil temperature sensor) is displayed.
A/F ALPHA-B1	%	The mean value of the air-fuel ratio feedback correction factor per cycle is indicated.	When the engine is stopped, a certain value is indicated. This data also includes the data for the air-fuel ratio learning control. Specification value is indicated on monitor screen under the following conditions. Reference: Select Display type: Line graph
INT/V SOL(B1)	%	The control value of the intake valve timing control solenoid valve (determined by ECM according to the input signals) is indicated. The advance angle becomes larger as the value increases.
IGN TIMING	BTDC	Indicates the ignition timing computed by ECM according to the input signals.	When the engine is stopped, a certain value is indicated.
FUEL INJ TIM	BTDC	Indicates the fuel injection timing computed by ECM according to the input signals.
A/F S1 HTR (B1)	%	Indicates the duty ratio of the Air fuel ratio (A/F) sensor 1 heater computed by ECM according to the input signals. The current flow to the heater becomes larger as the value increases.
EXH/V TIM B1	deg.CA	Indicates [ deg.CA] of exhaust camshaft advance angle.
FAN DUTY	%	Indicates a command value for cooling fan. The value is calculated by ECM based on input signals.
AC EVA TEMP	deg.C or deg.F	Indicates A/C evaporator temperature calculated according to the signal voltage of the intake air temperature sensor.
AC EVA TARGET	deg.C or deg.F	Indicates target A/C evaporator temperature sent from "A/C auto amp"
BAT TEMP SEN	V	The signal voltage from the battery temperature sensor is displayed.
THRTL STK CNT B1	--	NOTE: These items are displayed but are not applicable to this model.
ENG SPEED	RPM	Indicates the engine speed computed from the signal of the crankshaft position sensor and camshaft position sensor.	Accuracy becomes poor if engine speed drops below the idle RPM.
TRVL AFTER MIL	km or mile	Distance traveled while MIL is activated.
B/FUEL SCHDL	ms	"Base fuel schedule" indicates the fuel injection pulse width programmed into ECM, prior to any learned on board correction.	Specification value is indicated on monitor screen under the following conditions. Reference: Select Display type: Line graph
MASS AIRFLOW	g/s	Indicates the mass air flow computed by ECM according to the mass air flow sensor signal.
FUEL PRES SEN	MPa	Indicates the fuel rail pressure computed by ECM according to the input signals.
ACCEL SEN 1	V	The signal voltage of the accelerator pedal position sensor 1 is displayed.
ACCEL SEN 2	V	The converted value of the accelerator pedal position sensor signal voltage is displayed.	ACCEL SEN 2 signal is converted by ECM internally. Thus, they differs from ECM terminal voltage signal.
TP SEN 1-B1	V	The signal voltage of the throttle position sensor 1 B1 is displayed.
TP SEN 2-B1	V	The value converted from the signal voltage of the throttle position sensor 2 B1 is displayed.	TP SEN 2-B1 signal is converted by ECM internally. Thus, they differs from ECM terminal voltage signal.
FUEL INJ B1	msec	ECM-calculated injection pulse width of the fuel injector on the Bank 1 side.
I/P PULLY SPD	RPM	Indicates the engine speed computed from the input shaft revolution signal.
VEHICLE SPEED	km/h or mph	The vehicle speed computed from the vehicle speed signal sent from TCM is displayed.
TUMBLE POS SEN	V	The intake manifold runner control valve position sensor signal voltage is displayed.
AC PRESS SEN	V	The signal voltage from the refrigerant pressure sensor is displayed.
A/F SEN1 (B1)	V	The A/F signal voltage computed from the input signal of the air fuel ratio (A/F) sensor 1 is displayed.
SET VHCL SPD	km/h or mph	The preset vehicle speed is displayed.
VTC DTY EX B1	%	The control value of the exhaust valve timing control solenoid valve (determined by ECM according to the input signals) is indicated. The advance angle becomes larger as the value increases.
A/F ADJ-B1	--	Indicates the correction of a factor stored in ECM. The factor is calculated from the difference between the target air-fuel ratio stored in ECM and the air-fuel ratio calculated from A/F sensor 1 signal.
INT/V TIM(B1)	deg.CA	Indicates [ deg.CA] of intake camshaft advance angle.
H/P FUEL PUMP DEG	deg	Displays ECM-calculated fuel discharge position of the high pressure fuel pump.
FUEL PRES SEN V	mV	The signal voltage of FRP sensor is displayed.
EOP SENSOR	mV	The signal voltage of EOP sensor is displayed.
ECM TEMP 1	deg.C	Displays a temperature calculated from a signal of ECM temperature sensor 1.
ECM TEMP 2	deg.C	Displays a temperature calculated from a signal of ECM temperature sensor 2.
MASS AIR FLOW SENSOR (HZ)	Hz	The signal frequency of the mass air flow sensor is displayed.	When the engine is stopped, a certain value is indicated. Specification value is indicated on monitor screen under the following conditions. Reference: Select Display type: Line graph
A/F-S ATMSPHRC CRCT B1	--	Displays a determined value of atmospheric correction factor necessary for correcting an A/F sensor signal input to ECM. The signal used for the correction is an A/F sensor signal transmitted while driving under atmospheric pressure.
A/F-S ATMSPHRC CRCT UP B1	count	Displays the number of updates of the A/F sensor atmospheric correction factor.
EXHAUST GAS TEMP SEN 1 B1	V	The signal voltage of exhaust gas temperature sensor is displayed.
LOAD SIGNAL	On/Off	Indicates [On/Off] condition of the electrical load signal. ON.. Rear window defogger switch is ON or lighting switch is in 2nd position. OFF..Both rear window defogger switch and lighting switch are OFF.
AIR COND SIG	On/Off	Indicates [On/Off] condition of the air conditioner switch as determined by the air conditioner signal.
PW/ST SIGNAL	On/Off	Indicates [On/Off] condition of the power steering system (determined by the signal voltage of the power steering pressure sensor signal).
P/N POSI SW	On/Off	Indicates [On/Off] condition from the reverse/neutral position signal.
START SIGNAL	On/Off	Indicates start signal status [On/Off] computed by the ECM according to the signals of engine speed and battery voltage.	After starting the engine, [Off] is displayed regardless of the starter signal.
CLSD THL POS	On/Off	Indicates idle position [On/Off] computed by ECM according to the accelerator pedal position sensor signal.
HO2S2 MNTR(B1)	RICH/LEAN	Display of heated oxygen sensor 2 signal: RICH: means the amount of oxygen after three way catalyst is relatively small. LEAN: means the amount of oxygen after three way catalyst is relatively large.	When the engine is stopped, a certain value is indicated.
IGNITION SW	On/Off	Indicates [On/Off] condition from ignition switch signal.
HEATER FAN SW	On/Off	Indicates [On/Off] condition from the heater blower ON signal.
IDL A/V LEARN	YET/CMPLT	Displays the condition of Idle Air Volume Learning. YET..Idle air volume learning has not been performed yet. DONE..Idle air volume learning has already been performed successfully.
BRAKE SW	On/Off	Indicates [On/Off] condition from the stop lamp switch signal.
COMBUSTION	NOTE: These items are displayed but are not applicable to this model.
SWRL CONT S/V ^*	On/Off	The control condition of the intake manifold runner control valve (determined by ECM according to the input signals) is indicated. ON: Closed OFF: Open
AIR COND RLY	On/Off	The air conditioner relay control condition (determined by ECM according to the input signals) is indicated.
FUEL PUMP RLY	On/Off	Indicates the fuel pump relay control condition determined by ECM according to the input signals.
VENT CONT/V	On/Off	The control condition of the EVAP canister vent control valve (determined by ECM according to the input signals) is indicated. ON: Closed OFF: Open
THRTL RELAY	On/Off	Indicates the throttle control motor relay control condition determined by the ECM according to the input signals.
DIST SW	On/Off	Indicates [On/Off] condition from DISTANCE switch signal.
BRAKE SW2	On/Off	Indicates [On/Off] condition of stop lamp switch signal.
BRAKE SW1	On/Off	Indicates [On/Off] condition from brake pedal position switch signal.
SET SW	On/Off	Indicates [On/Off] condition from SET - switch signal.
RESUME/ACC SW	On/Off	Indicates [On/Off] condition from RES + switch signal.
CANCEL SW	On/Off	Indicates [On/Off] condition from CANCEL switch signal.
MAIN SW	On/Off	Indicates [On/Off] condition from MAIN switch signal.
SET LAMP	On/Off	Indicates [On/Off] condition of SET indicator determined by the ECM according to the input signals.
AT OD CANCEL	On/Off	Indicates [On/Off] condition of A/T O/D cancel request signal.	For M/T models, always [Off] is displayed.
AT OD MONITOR	On/Off	Indicates [On/Off] condition of A/T O/D according to the input signal from the TCM.	For M/T models, always [Off] is displayed.
CRUISE LAMP	On/Off	Indicates [On/Off] condition of CRUISE indicator determined by the ECM according to the input signals.
LO SPEED CUT	NON/CUT	Indicates the vehicle cruise condition. NON..Vehicle speed is maintained at the ASCD set speed. CUT..When the vehicle speed decreased lower than the ASCD minimum set speed, ASCD operation is cut off.
VHCL SPD CUT	NON/CUT	Indicates the vehicle cruise condition. NON..Vehicle speed is maintained at the ASCD set speed. CUT..When the vehicle speed decreased to excessively low speed compared with the ASCD set speed, ASCD operation is cut off.
ALT DUTY SIG	On/Off	The control condition of the power generation voltage variable control (determined by ECM according to the input signals) is indicated. ON: Power generation voltage variable control is active. OFF: Power generation voltage variable control is inactive.
HO2S2 HTR (B1)	On/Off	Indicates [On/Off] condition of heated oxygen sensor 2 heater determined by ECM according to the input signals.
HO2 S2 DIAG1 (B1)	INCMP/CMPLT	Indicates DTC P0139 self-diagnosis (delayed response) condition. INCMP: Self-diagnosis is incomplete. CMPLT: Self-diagnosis is complete.
HO2 S2 DIAG2 (B1)	INCMP/CMPLT	Indicates DTC P0139 self-diagnosis (slow response) condition. INCMP: Self-diagnosis is incomplete. CMPLT: Self-diagnosis is complete.
EVAP LEAK DIAG	YET/CMPLT	Indicates the condition of EVAP leak diagnosis. YET: EVAP leak diagnosis has not been performed yet. CMPLT: EVAP leak diagnosis has been performed successfully.
EVAP DIAG READY	On/Off	Indicates the ready condition of EVAP leak diagnosis. ON: Diagnosis has been ready condition. OFF: Diagnosis has not been ready condition.
SYSTEM 1 DIAGNOSIS A B1	INCMP/CMPLT	Indicates DTC P219A self-diagnosis condition. INCMP: Self-diagnosis is incomplete. CMPLT: Self-diagnosis is complete.
A/F SEN1 DIAG1 (B1)	INCMP/CMPLT	Indicates DTC P015A or P015B self-diagnosis condition. INCMP: Self-diagnosis is incomplete. CMPLT: Self-diagnosis is complete.
A/F SEN1 DIAG2(B1)	INCMP/CMPLT	Indicates DTC P014C or P014D self-diagnosis condition. INCMP: Self-diagnosis is incomplete. CMPLT: Self-diagnosis is complete.
SYSTEM 1 DIAGNOSIS B B1	ABSNT/PRSNT	Indicates DTC P219A self-diagnosis condition. ABSNT: Self-diagnosis standby PRSNT: Under self-diagnosis
A/F SEN1 DIAG3(B1)	ABSNT/PRSNT	Indicates DTC P014C, P014D, P015A or P015B self-diagnosis condition. ABSNT: The vehicle condition is not within the diagnosis range. PRSNT: The vehicle condition is within the diagnosis range.