Door Assembly
- General Information
- Specification(S)
- Sealant
- Component Identifications
- Special Tools
- Door Diagnosis
- Standard Flow Of Diagnostic Troubleshooting
- Trouble Symptom Chart < Central Door Locking System >
- Symptom Procedures < Central Door Locking System >
- INSPECTION PROCEDURE A-1: Central Door Locking System does not Work at All
- INSPECTION PROCEDURE A-2: Central Door Locking System does not Operate even when Door Lock Switch of Power Window Main Switch Operated (Door Lock Switch of Front Power Window Sub Switch Operates Normally)
- INSPECTION PROCEDURE A-3: Central Door Locking System does not Operate even when Door Lock Switch of Front Power Window Sub Switch Operated (Door Lock Switch of Power Window Main Switch Operates Normally)
- INSPECTION PROCEDURE A-4: A Door or a Liftgate cannot be Locked or Unlocked by the Central Door Locking System
- INSPECTION PROCEDURE A-5: Selector "P" Position-linked Door Unlock Function does not Operate < CVT >
- INSPECTION PROCEDURE A-6: Ignition "LOCK (OFF)" Position-linked Door Unlock Function does not Operate
- Diagnosis Code Chart < Driver's Side Power Window >
- Diagnostic Trouble Code Procedures < Driver Side Power Window >
- CODE NO. L0730: P/W (DR) SW pulse 1 disconnection
- CODE NO. L0732: P/W (DR) SW pulse 2 disconnection
- CODE NO. L0734: P/W (DR) Above window position
- CODE NO. L0736: P/W (DR) Sensor fail (ground)
- CODE NO. L0740: P/W (DR) 3 times jam - protection
- CODE NO. L0746: P/W (DR) Parameter read fail; CODE NO. L0750: P/W (DR) Position read fail
- Trouble Symptom Chart < Power Window >
- Symptom Procedures < Power Window >
- INSPECTION PROCEDURE B-1: Power Windows do not Work at All
- INSPECTION PROCEDURE B-2: Driver's Power Window does not Work by means of The Power Window Main Switch
- INSPECTION PROCEDURE B-3: Relevant Power Window(s) does not Work by means of the Front and Rear Passenger's Power Window Sub Switches
- INSPECTION PROCEDURE B-4: Front and/or Rear Passenger's Power Window(s) do not work by means of the Power Window Main Switch
- INSPECTION PROCEDURE B-5: The Power Window Timer Function does not Work Normally
- INSPECTION PROCEDURE B-7: Window Glass Lowers Automatically while it is Rising < Driver's Side Only >
- Check At Ecu Terminal
- Introduction To Glass And Door Diagnosis
- Glass And Door Diagnostic Troubleshooting Strategy
- Symptom Chart
- Symptom Procedures
- INSPECTION PROCEDURE 1: Water Leak Through Door Window Glass
- INSPECTION PROCEDURE 2: Door Window Glass Malfunction
- INSPECTION PROCEDURE 3: Water Leak Through Door Edge
- INSPECTION PROCEDURE 4: Water Leak from Door Center
- INSPECTION PROCEDURE 5: Door Hard to Open
- INSPECTION PROCEDURE 6: Door does not Open or Close Completely
- INSPECTION PROCEDURE 7: Uneven Gap Between
- INSPECTION PROCEDURE 8: Wind Noise Around Door
- How To Locate Wind Noise
- On-Vehicle Service
- Door Adjustment
- Door Window Glass Adjustment
- Power Window Check
- Adjustment Of Faulty Power Window
- Power Window Safety Mechanism Check < Driver's Side Door >
- Power Window Timer Function Check
- Power Window Operating Current Check
- Learning Procedures Of Power Window Fully Closed Position < Driver's Side Door >
- Central Door Locking System Check
- Key-In Prevention Function Check
- Selector "P" Position-Linked Door Unlocking Function Check < CVT >
- Ignition "Lock (Off)" Position-Linked Door Unlocking Function Check
- Door Latch Assembly Inspection
- Door Outside Handle Assembly Play Check
- Door Inside Handle Check
- Customization Function
- Door Assembly
- Door Glass And Regulator
- Door Handle And Latch
- Window Glass RUNCHANNEL And Door Opening Weatherstrip