Chassis Electrical
- Battery
- Ignition Switch
- General Description
- Ignition Key Reminder Tone Alarm And Door Lock Prevention Function Diagnosis
- Encrypted Code Registration Criteria Table
- Immobilizer System Diagnosis
- Introduction To Immobilizer System Diagnosis
- Immobilizer System Diagnostic Troubleshooting Strategy
- Diagnosis Function
- Diagnostic Trouble Code Chart
- Diagnostic Trouble Code Procedures
- Symptom Chart
- Symptom Procedures
- Data List Reference Table
- Check At Immobilizer-Ecu
- Special Tools
- On-Vehicle Service
- Ignition Switch
- Combination Meter Assembly & Vehicle Speed Sensor
- General Description
- Combination Meters Assembly And Vehicle Speed Sensor Diagnosis
- Troubleshooting Strategy
- Diagnosis Function
- Diagnostic Trouble Code Chart
- Diagnostic Trouble Code Procedures
- DTC B1200: Defective Odometer
- DTC B1201: Defective Fuel Gauge
- DTC U1073: Bus Off
- DTC U1100: Powertrain Control Module Time-Out (Related To Engine) DTC U1101: Powertrain Control Module Time-Out (Related To A/T)
- DTC U1102: Abs-Ecu Time-Out
- DTC U1109: ETACS-Ecu Time-Out
- DTC U1112: SRS-Ecu Time-Out
- DTC U1120: Failure Information On Powertrain Control Module (Related To Engine)
- DTC U1206: Flag Invalid
- Symptom Chart
- Symptom Procedures
- Inspection Procedure 1: Communication With Scan Tool Is Not Possible
- Inspection Procedure 2: Power Supply Circuit; Inspection Procedure 3: Odometer And Trip Meter Are Not Displayed; Inspection Procedure 4: All The Needle Meters Do Not Work; Inspection Procedure 5: When The Ignition Switch Is Turned To The On Position, The Indicator And Warning Lights Do Not Illuminate
- Inspection Procedure 6: Speedometer Does Not Work; Inspection Procedure 7: The Fuel Gauge Needle Moves Excessively
- Inspection Procedure 8: Tachometer Does Not Work
- Inspection Procedure 9: Fuel Gauge Does Not Work (Other Meters Work)
- Inspection Procedure 10: Engine Coolant Temperature Gauge Does Not Work (Other Meters Work)
- Data List Reference Table
- Actuator Test Reference Table
- Combination Meter Terminal Check
- Special Tools
- On-Vehicle Service
- Combination Meter Assembly
- Headlight, Front Side Marker Light & Position Light Assembly
- Fog Light
- Rear Combination Light
- Dome Light
- License Plate Light
- High-Mounted Stoplight
- Rheostat
- Hazard Warning Light Switch
- Column Switch
- Horn
- Accessory Socket
- Radio With Cd Player
- General Description
- Radio With Cd Player, Speaker And Antenna Diagnosis
- Introduction To Audio System Diagnosis
- Audio Error Codes
- Audio System Diagnostic Troubleshooting Strategy
- Symptom Chart
- Symptom Procedures
- Inspection Procedure 1: When Power Switch Is Turned "On," No Power Is Available
- Inspection Procedure 2: When Remote Controlled Radio Power Switch Is Turned "On," No Power Is Available. But Radio, Cd Player And Cd Changer Power Switch Is Available < Vehicles With Seven Speakers >
- Inspection Procedure 3: The System Does Not Recognize The Remote Controlled Radio Switch (RH) Only < Vehicles With Seven Speakers >
- Inspection Procedure 4: The System Does Not Recognize The Remote Controlled Radio Switch (LH) Only < Vehicles With Seven Speakers >
- Inspection Procedure 5: No Sound < Vehicles With Audio Amplifier >
- Inspection Procedure 6: No Sound From One Speaker < Vehicles With Six Speakers >
- Inspection Procedure 7: No Sound From One Speaker < Vehicles With Seven Speakers >
- Inspection Procedure 8: Noise Is Present While Moving (Am)
- Inspection Procedure 9: Noise Is Present While Moving (Fm)
- Inspection Procedure 10: Sound Mixed With Noise, Only At Night (Am)
- Inspection Procedure 11: Noise Is Overpowering Both Am And Fm
- Inspection Procedure 12: Excessive Noise On Am And Fm
- Inspection Procedure 13: Noise Is Detected With Engine Running
- Inspection Procedure 14: Noise Appears During Vibration Or Shocks
- Inspection Procedure 15: Noise Is Present While Moving (Fm)
- Inspection Procedure 16: Constant Noise
- Inspection Procedure 17: No Reception (Am)
- Inspection Procedure 18: Poor Reception
- Inspection Procedure 19: Distortion On Am And/Or Fm
- Inspection Procedure 20: Distortion On Fm Only
- Inspection Procedure 21: Auto Select Function Inoperative, Too Few Automatic Stations Are Selected
- Inspection Procedure 22: Preset Stations Are Erased
- Inspection Procedure 23: Cd Cannot Be Inserted
- Inspection Procedure 24: No Sound (Cd Only)
- Inspection Procedure 25: Cd Sound Skips
- Inspection Procedure 26: Sound Quality Is Poor
- Inspection Procedure 27: Cd Cannot Be Ejected
- On-Vehicle Service
- Special Tool
- Radio With Cd Player Removal And Installation
- Speaker
- Amplifier
- Antenna
- Video Entertainment System (VES)
- General Description
- Special Tool
- Video Entertainment System Diagnosis
- Troubleshooting Strategy
- Symptom Chart
- Symptom Procedures
- Main Unit Terminal Voltage
- Rear Display Unit (Overhead Type)
- Rear Window Defogger
- Multi-Center Display
- General Description
- Multi-Center Display System < Middle Grade Type >
- Failure Diagnosis Service Mode Function < Middle Grade Type >
- Multi-Center Display Diagnostic Trouble Code Diagnosis
- On-Board Diagnostics
- Diagnosis Function
- Diagnostic Trouble Code Chart
- Diagnostic Trouble Code Procedures
- DTC 010: Bus Off
- DTC 011: Powertrain Control Module Time-Out (Related To Engine); DTC 012: Powertrain Control Module Time-Out (Related To A/T)
- DTC 013: A/C-Ecu Time-Out
- DTC 014: Combination Meter Time-Out
- DTC 019: ETACS-Ecu Time-Out
- DTC 020: Failures Information On Powertrain Control Module (Related To Engine)
- DTC 021: Failures Information On Combination Meter
- DTC 022: Failures Information On A/C-Ecu
- Diagnosis
- Equipment Diagnosis
- Inspection Procedure 1: Communication With Scan Tool Is Not Possible (Middle Grade Type)
- Inspection Procedure 2: The Multi-Center Display Does Not Show Any Information (Middle Grade Type)
- Inspection Procedure 3: The Multi-Center Display Does Not Show Any Information (Low Grade Type)
- Inspection Procedure 4: The A/C Display Shows "Communication Error", And Then Can Not Proceed To Next Screen (Middle Grade Type)
- Inspection Procedure 5: The Ambient Air Temperature Display Shows "Com Error" Or "--°C (--°F)" (Middle Grade Type)
- Inspection Procedure 6: On The Audio Screen, "Communication Error" Can Not Proceed To Next Screen (Middle Grade Type)
- Inspection Procedure 7: The Compass Can Not Be Calibrated Manually, Or Becomes Out Of Calibration Easily (Middle Grade Type)
- On-Vehicle Service
- Ambient Temperature Sensor
- Theft Alarm
- Specifications