Front Seat Assembly: Reassembly

INSTALL FRONT SEAT ADJUSTER SUB-ASSEMBLY RH (for Front Passenger Seat)
INSTALL FRONT SEAT TRACK ASSEMBLY OUTER (for Driver Seat)
INSTALL POWER SEAT MOTOR ASSEMBLY (for Driver Seat)
INSTALL SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY (for Driver Seat)
1. Using a "Torx" socket wrench (T40), install the separate type front seat cushion spring assembly with the 4 "Torx" bolts.
2. Install the front seat cushion frame sub-assembly with the 4 bolts.
  Torque: 19 N*m (194 kgf*cm, 14 ft.*lbf)
INSTALL FRONT SEAT SIDE AIRBAG ASSEMBLY
1. Install the front seat side airbag assembly with the 2 nuts.
  Torque: 5.5 N*m (56 kgf*cm, 49 in.*lbf)
2. Install the clamps.
INSTALL FRONT SEAT WIRE
INSTALL OCCUPANT CLASSIFICATION ECU (for Front Passenger Seat) (See INSTALLATION )
INSTALL SEAT POSITION SENSOR (for Driver Seat) (See INSTALLATION )
INSTALL SEAT SLIDE POSITION SENSOR PROTECTOR (for Driver Seat)
INSTALL SEAT HEATER CONTROL SUB-ASSEMBLY (w/ Seat Heater System)
INSTALL LUMBAR SUPPORT ADJUSTER ASSEMBLY
INSTALL FRONT SEAT CUSHION SHIELD LOWER RH
INSTALL FRONT SEAT CUSHION SHIELD LOWER LH
INSTALL RECLINING ADJUSTER INSIDE COVER RH
INSTALL RECLINING ADJUSTER INSIDE COVER LH
INSTALL RH SEAT RECLINING ADJUSTER INSIDE COVER
INSTALL LH SEAT RECLINING ADJUSTER INSIDE COVER
INSTALL SEPARATE TYPE FRONT SEATBACK COVER
1. Using hog ring pliers, install the separate type front seatback cover to the separate type front seatback pad with new hog rings.
  NOTE:
  - Be careful not to damage the cover.
  - When installing the hog rings, take care to minimize wrinkles as much as possible.
    
    Fig 1: Identifying Front Seatback Cover LH
    Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL SEPARATE TYPE FRONT SEATBACK COVER WITH PAD
1. Install the separate type front seatback cover with pad to the separate type front seat cushion spring assembly.
2. Install the separate type front seatback cover bracket with the nut.
  Torque: 5.6 N*m (57 kgf*cm, 50 in.*lbf)
  NOTE:
  - For vehicles with side airbags, the side airbags may not be activated normally unless the separate type front seatback cover is securely installed.
  - Check that the strap is not twisted after installing the bracket.
  - Install the bracket securely.
    
    Fig 2: Identifying Separate Type Front Seatback Cover Bracket With Pad
    Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
3. Install the hook.
INSTALL FRONT SEAT HEADREST SUPPORT
INSTALL FRONT SEAT HEADREST SUPPORT
INSTALL FRONT SEATBACK BOARD SUB-ASSEMBLY
INSTALL SEAT ARMREST ASSEMBLY
1. Install the seat armrest assembly with the bolt and 2 washers.
  Torque: 37 N*m (377 kgf*cm, 27 ft.*lbf)
INSTALL SEAT ARMREST COVER
INSTALL FRONT SEAT HEADREST ASSEMBLY
INSTALL SEPARATE TYPE FRONT SEAT CUSHION PAD
INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER
1. Using hog ring pliers, install the separate type front seat cushion cover to the separate type front seat cushion pad with new hog rings.
  NOTE:
  - Be careful not to damage the cover.
  - When installing the hog rings, take care to minimize wrinkles as much as possible.
    
    Fig 3: Identifying Front Seatback Cover LH
    Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER WITH PAD
INSTALL FRONT SEAT INNER BELT ASSEMBLY (See INSTALLATION )
INSTALL FRONT POWER SEAT SWITCH
INSTALL FRONT SEAT CUSHION SHIELD INNER NO.1
INSTALL FRONT SEAT CUSHION SHIELD INNER
INSTALL FRONT SEAT CUSHION SHIELD
INSTALL POWER SEAT SWITCH ASSEMBLY (for Driver Seat)
INSTALL FRONT SEAT CUSHION SHIELD ASSEMBLY
INSTALL SLIDE AND VERTICAL POWER SEAT SWITCH KNOB
INSTALL RECLINING POWER SEAT SWITCH KNOB