Lumbar Support Adjuster Assembly: Installation

HINT:

Use the same procedures for the LH and RH side.
A bolt without a torque specification is shown in the standard bolt chart (see SPECIFIED TORQUE FOR STANDARD BOLTS ).

INSTALL LUMBAR SUPPORT ADJUSTER ASSEMBLY
1. Install the lumbar support adjuster with the 2 screws.
2. Connect the connector.
INSTALL SEPARATE TYPE FRONT SEATBACK COVER WITH PAD
1. Install the seatback cover (with pad) to the seat frame.
2. Install the 2 headrest supports.
3. Fully cover the airbag with the 2 seatback cover brackets and install the nut.
  Torque: 5.5 N*m (56 kgf*cm, 49 in.*lbf)
  CAUTION:
  - For vehicles with side airbags, the seatback cover must be securely installed. Otherwise, the side airbags may not deploy properly.
  - Make sure that the strap is not twisted after installing the bracket.
  - Install the bracket securely.
4. Using hog ring pliers, install the seatback cover (with pad) to the seat adjuster with new hog rings, and attach the hooks.
5. Install the 2 headrest supports.
  
  Fig 1: Identifying Seatback Cover (With Pad) Hog Rings
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
6. Install the front seatback cover inner and outer with the 4 bolts.
  
  Fig 2: Identifying Front Seatback Cover Bolts (Inner And Outer)
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL FRONT SEATBACK BOARD SUB-ASSEMBLY
1. Attach the 2 claws and install the seatback board with the 2 screws.
INSTALL FRONT SEAT CUSHION SHIELD ASSEMBLY
1. Attach the 2 claws and install the cushion shield.
2. Install the 5 screws.
3. Connect the 2 rubber bands of the front seatback board to the seat frame.
4. Connect the connector to the interior No. 1 illumination light.
INSTALL RECLINING POWER SEAT SWITCH KNOB
INSTALL SLIDE AND VERTICAL POWER SEAT SWITCH KNOB
INSTALL FRONT SEAT INNER BELT ASSEMBLY (See INSTALLATION )
INSTALL FRONT SEAT ASSEMBLY
1. Place the seat in the cabin.
  NOTE: Be careful not to damage the vehicle body.
2. Connect the connector under the seat.
3. Connect the cable to the negative (-) battery terminal.
4. Operate the power seat switch knob and move the seat to the foremost position.
5. Install the 2 bolts on the rear side of the seat.
  Torque: 36.8 N*m (375 kgf*cm, 27 ft.*lbf)
  
  HINT:
  
  Tighten the 2 bolts in the order indicated in the illustration.
  
  Fig 3: Identifying Tightening Sequence Of Bolts
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
6. Attach the 4 claws to install the seat track bracket cover rear inner and outer.
7. Operate the power seat switch knob and move the seat to the rearmost position.
8. Install the 2 bolts on the front side of the seat.
  Torque: 36.8 N*m (375 kgf*cm, 27 ft.*lbf)
  
  HINT:
  
  Tighten the 2 bolts in the order indicated in the illustration.
9. Attach the 4 claws to install the seat track bracket cover front inner and outer.
INSTALL FRONT SEAT OUTER BELT ASSEMBLY
1. Move the seat using the power seat switch knob so that the seat belt anchor bolt is revealed.
2. Install the front seat outer belt anchor with the bolt.
  Torque: 42 N*m (428 kgf*cm, 31 in.*lbf)
  
  Fig 4: Identifying Front Seat Outer Belt Anchor With Bolt
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
3. Install the seat belt anchor cover cap.
4. Install the front seat belt hole cover.
PERFORM INITIALIZATION
1. Perform initialization (see INITIALIZATION (2006/02-2006/07) ).
  NOTE: Certain systems need to be initialized after disconnecting and reconnecting the cable from the negative (-) battery terminal.
CHECK SRS WARNING LIGHT
Check the SRS warning light (see DIAGNOSIS SYSTEM (2006/02-2006/07) ).
INSPECT FRONT SEAT ASSEMBLY
1. Check the power seat operation.
2. Check the seat heater operation (with seat heater).
  1. Turn the power switch ON (IG).
  2. Turn the seat heater switch ON.
  3. Wait 5 minutes or more and confirm that the seat surface becomes warm.