Common Specs & Procedures
K900 COMMON SPECS & PROCEDURES
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | SPECIFICATION | ||
| Torque | TIGHTENING TORQUES | ||
| Axle Nut/Hub Nut | |||
| Front | N/A | ||
| Rear | 196.1-274.5 N.m (20.0-28.0 kgf.m, 144.7- 202.5 lb. ft.) | ||
| Battery | BATTERY (3.8L) or BATTERY (5.0L) | ||
| Brakes | |||
| Bleeding Sequence | Refer to BRAKE SYSTEM BLEEDING and ESP SYSTEM BLEEDING . | ||
| Disc Brakes | |||
| Service Specifications | SPECIFICATIONS | ||
| Torque | TIGHTENING TORQUES | ||
| Drum Brakes | |||
| Service Specifications | N/A | ||
| Torque | N/A | ||
| Charging | |||
| Generator | CHARGING SYSTEM (3.8L) or CHARGING SYSTEM (5.0L) | ||
| Torque | Refer to TIGHTENING TORQUES (3.8L) or TIGHTENING TORQUES (5.0L) . | ||
| Drive Belts | |||
| Adjustment | REMOVAL AND INSTALLATION (3.8L) or REMOVAL AND INSTALLATION (5.0L) | ||
| Drive Belt Routing | Refer to Drive Belt Routing figure under REMOVAL AND INSTALLATION (3.8L) or REMOVAL AND INSTALLATION (5.0L) . | ||
| Engine Cooling | |||
| General Service Specifications | Refer to Cooling System in chart under SPECIFICATIONS (3.8L) or SPECIFICATIONS (5.0L) | ||
| Radiator Cap Pressure | 13.51-17.78 psi (93.16-122.58 kPa) | ||
| Thermostat R & I | THERMOSTAT (3.8L) or WATER TEMPERATURE CONTROL ASSEMBLY (5.0L) | ||
| Water Pump R & I | WATER PUMP (3.8L) or WATER PUMP (5.0L) | ||
| Engine Mechanical | |||
| Compression | COMPRESSION TEST (3.8L) or COMPRESSION TEST (5.0L) | ||
| Oil Pressure (3.8L) | 130 kPa (1.32 kgf/cm2 , 18.77 psi) at 1000 RPM, 110°C (230°F) | ||
| Oil Pressure (5.0L) | 156.91 kPa (1.6 kgf/cm2 , 22.76 psi) or above, 110°C (230°F) | ||
| Overhaul | SPECIFICATIONS (3.8L) or SPECIFICATIONS (5.0L) | ||
| Torque | TIGHTENING TORQUES (3.8L) or TIGHTENING TORQUES (5.0L) | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE/FLUIDS tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flywheel/Flex Plate/Drive Plate Torque (3.8L) | 71.6-75.5 N.m (52.80-55.9) | ||
| Flywheel/Flex Plate/Drive Plate Torque (5.0L) | 98.1-107.9 N.m (72.3-79.6) | ||
| Fuel System | |||
| Pressure Specification (3.8L) | Low Pressure Fuel Line: 480-520 kPa (4.7-5.3 kgf/cm2
, 69.7-75.4 psi) High Pressure Fuel Line: 2.0 ~ 15.0 MPa (20 ~ 153 kgf/cm, 284.4 ~2176.2 psi) |
||
| Pressure Specification (5.0L) | Low Pressure Fuel Line: 480-520 kPa (4.7-5.3 kgf/cm2
, 69.7-75.4 psi) High Pressure Fuel Line: 2.0 ~ 14.7 MPa (20 ~ 150.0 kgf/cm, 284.5 ~2133.5 psi) |
||
| Fuel Pressure Test Procedure | FUEL PRESSURE TEST (LOW PRESSURE SYSTEM) (3.8L) or FUEL PRESSURE TEST (LOW PRESSURE SYSTEM) (5.0L) | ||
| Fuel Filter Location | Fuel filter is part of fuel pump module | ||
| Fuel Filter R & I | FUEL FILTER | ||
| Ignition | |||
| Firing Order & Cylinder Identification | FIRING ORDER & CYLINDER IDENTIFICATION | ||
| Ignition Wires (Resistance) | Coil on plug. Refer to IGNITION COIL (3.8L) or IGNITION COIL (5.0L) . | ||
| Ignition Wires (Routing) | Coil on plug. | ||
| Spark Plug | |||
| Type: DILKR7A11 | |||
| Gap | 1.0-1.1 mm (0.0394-0.0433 in.) | ||
| Torque | 14.7-24.5 N.m (1.5-2.5 kgf.m, 10.9-18.1 lb-ft) | ||
| Starting | |||
| Starter | Refer to STARTING SYSTEM - 3.8L or STARTING SYSTEM - 5.0L . | ||
| Torque | Refer to TIGHTENING TORQUES (3.8L) or TIGHTENING TORQUES (5.0L) . | ||
| Wheel Alignment | |||
| Adjustment Specifications | ALIGNMENT | ||
| Torque | TIGHTENING TORQUES | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 88.3-107.9 N.m (9.0-11.0 kgf.m, 65.1-79.6 lb-ft) | ||