Repair Procedures: Removal: 2WD

CAUTION:

When lifting a vehicle using a lift, be careful not to damage the lower parts of the vehicle (floor under cover, fuel filter, fuel tank, canister).

(Refer to General Information - "LIFT AND SUPPORT POINTS ")

Loosen the front wheel nuts slightly.
Raise the vehicle, and make sure it is securely supported.
Remove the front wheel and tire.
(Refer to Suspension System - "WHEEL ")
Remove the brake caliper.
(Refer to Brake System - "FRONT DISC BRAKE ")
Loosen the screw and then removing the front brake disc (A).
Tightening torque:

4.9 - 5.8 N.m (0.5 - 0.6 kgf.m, 3.6 - 4.3 lb-ft)

Courtesy of HYUNDAI MOTOR AMERICA
Loosen the dust cover bolts and then removing the dust cover (A).
Tightening torque:

10.8 - 12.7 N.m (1.1 - 1.3 kgf.m, 8.0 - 9.4 lb-ft)

Courtesy of HYUNDAI MOTOR AMERICA
Remove the bolts and then brake cooling cover (A).
Tightening torque:

7.8 - 11.8 N.m (0.8 - 1.2 kgf.m, 5.8 - 8.7 lb-ft)

Courtesy of HYUNDAI MOTOR AMERICA
Remove the wheel speed sensor bracket bolt (A).
Tightening torque:

6.9 - 10.8 N.m (0.7 - 1.1 kgf.m, 5.1 - 7.9 lb-ft)

Courtesy of HYUNDAI MOTOR AMERICA
Remove the brake tube bracket bolt (A).
Tightening torque:

6.9 - 10.8 N.m (0.7 - 1.1 kgf.m, 5.1 - 7.9 lb-ft)

Courtesy of HYUNDAI MOTOR AMERICA
Remove the compression arm pin and tie rod end ball joint nut (A).
Tightening torque:

88.3 - 107.9 N.m (9.0 - 11.0 kgf.m, 65.1 - 79.6 lb-ft)

Courtesy of HYUNDAI MOTOR AMERICA
Remove the tie rod end ball joint (A) from the knuckle by using the SST (09568-2J100).

Courtesy of HYUNDAI MOTOR AMERICA
Remove the front wheel guard.
(Refer to Body - "FRONT WHEEL GUARD ")
Remove the under cover.
(Refer to Engine Mechanical System - "ENGINE ROOM UNDER COVER ")
Loosen the bolt and nut and then removing the tension arm (A) from the sub frame.
Tightening torque:

156.9 - 176.5 N.m (16.0 - 18.0 kgf.m, 115.7 - 130.2 lb-ft)

Courtesy of HYUNDAI MOTOR AMERICA
Disconnect the wheel speed sensor connector (A).

Courtesy of HYUNDAI MOTOR AMERICA
Remove the lateral arm pin and castle nut (A).
Tightening torque:

88.3 - 107.9 N.m (9.0 - 11.0 kgf.m, 65.1 - 79.6 lb-ft)

Courtesy of HYUNDAI MOTOR AMERICA
Remove the lateral arm from the knuckle by using the SST (09568-2J100).

Courtesy of HYUNDAI MOTOR AMERICA
Remove the tension arm pin and castle nut (A).
Tightening torque:

88.3 - 107.9 N.m (9.0 - 11.0 kgf.m, 65.1 - 79.6 lb-ft)

Courtesy of HYUNDAI MOTOR AMERICA
Remove the tension arm from the by using the SST (09568-2J100).

Courtesy of HYUNDAI MOTOR AMERICA
Loosen the hub assembly bolts and then removing the hub assembly (A).
Tightening torque:

88.3 - 107.9 N.m (9.0 - 11.0 kgf.m, 65.1 - 79.6 lb-ft)

Courtesy of HYUNDAI MOTOR AMERICA
Remove the knuckle upper bolt and nut.
Tightening torque:

78.5 - 98.1 N.m (8.0 - 10.0 kgf.m, 57.9 - 72.3 lb-ft)

Courtesy of HYUNDAI MOTOR AMERICA
Remove the knuckle by using the SST (0K517-J5100).
Reference value: Below 8.0 mm (0.31 in.)

Courtesy of HYUNDAI MOTOR AMERICA
CAUTION:
- Be careful not to exceed 8 mm (0.31 in.) because it may cause knuckle quality issues.