| U0100:00 |
Lost Communication with ECM/PCM "A": No Sub Type Information |
GO to PINPOINT TEST W
. |
| U0140:00 |
Lost Communication With Body Control Module: No Sub Type Information |
GO to PINPOINT TEST Y
. |
| U0155:00 |
Lost Communication With Instrument Panel Cluster (IPC) Control Module: No Sub Type Information |
GO to PINPOINT TEST AB
. |
| U0401:00 |
Invalid Data Received from ECM/PCM A: No Sub Type Information |
RETRIEVE and FOLLOW DTCs present in the PCM. REFER to
ELECTRONIC ENGINE CONTROLS - DIESEL ENGINES
. |
| U0422:00 |
Invalid Data Received From Body Control Module: No Sub Type Information |
RETRIEVE and FOLLOW DTCs present in the BCM. REFER to
MULTIFUNCTION ELECTRONIC MODULES
. |
| U0423:00 |
Invalid Data Received from Instrument Panel Cluster Control Module: No Sub Type Information |
RETRIEVE and FOLLOW DTCs present in the IPC. REFER to
INSTRUMENTATION, MESSAGE CENTER, AND WARNING CHIMES
. |
| U2100:00 |
Initial Configuration Not Complete: No Sub Type Information |
- This DTC sets due to incomplete or incorrect PMI procedures. CHECK the vehicle service history for recent service actions related to the Global Positioning System Module (GPSM).
- If there have been recent service actions with the Global Positioning System Module (GPSM), REPEAT/PERFORM the PMI procedure as directed by the diagnostic scan tool. REFER to Programmable Module Installation (PMI) in
MODULE CONFIGURATION
.
- If there have been no recent service actions, INSTALL a new Global Positioning System Module (GPSM) to correct the failure to retain configuration data. REFER to GLOBAL POSITIONING SYSTEM MODULE (GPSM)
.
|
| U2101:00 |
Control Module Configuration Incompatible: No Sub Type Information |
- This DTC sets due to incomplete or incorrect PMI procedures. CHECK the vehicle service history for recent service actions related to the Global Positioning System Module (GPSM).
- If there have been recent service actions with the Global Positioning System Module (GPSM), REPEAT/PERFORM the PMI procedure as directed by the diagnostic scan tool. REFER to Programmable Module Installation (PMI) in
MODULE CONFIGURATION
.
- If there have been no recent service actions, INSTALL a new Global Positioning System Module (GPSM) to correct the failure to retain configuration data. REFER to GLOBAL POSITIONING SYSTEM MODULE (GPSM)
.
|
| U3000:09 |
Control Module: Component Failure |
- CLEAR the DTC.
- WAIT at least 10 seconds.
- REPEAT the self-test.
- If DTC U3000:09 is retrieved again, DISCONNECT the battery for 1 minute, then reconnect it.
- CLEAR the DTC.
- WAIT at least 10 seconds.
- REPEAT the self-test.
- If DTC U3000:09 is retrieved again, INSTALL a new Global Positioning System Module (GPSM). REFER to GLOBAL POSITIONING SYSTEM MODULE (GPSM)
.
|
| U3000:41 |
Control Module: General Checksum Failure |
- CLEAR the DTC.
- WAIT at least 10 seconds.
- REPEAT the self-test.
- If DTC U3000:41 is retrieved again, INSTALL a new Global Positioning System Module (GPSM). REFER to GLOBAL POSITIONING SYSTEM MODULE (GPSM)
.
|
| U3000:42 |
Control Module: General Memory Failure |
- CLEAR the DTC.
- WAIT at least 10 seconds.
- REPEAT the self-test.
- If DTC U3000:42 is retrieved again, INSTALL a new Global Positioning System Module (GPSM). REFER to GLOBAL POSITIONING SYSTEM MODULE (GPSM)
.
|
| U3003:16 |
Battery Voltage: Circuit Voltage Below Threshold |
GO to PINPOINT TEST AH
. |
| U3003:17 |
Battery Voltage: Circuit Voltage Above Threshold |
GO to PINPOINT TEST AI
. |