Common Specs & Procedures
RAM PROMASTER COMMON SPECS & PROCEDURES
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | Refer to A/C SYSTEM | ||
| Torque | Refer to TORQUE SPECIFICATIONS | ||
| Axle Nut/Hub Nut | |||
| Front | 350 ft. lbs. (475 N.m) | ||
| Rear | N/A | ||
| Battery | Refer to BATTERY | ||
| Brakes | |||
| Bleeding Sequence | Base Brakes: refer to BASE BRAKE BLEEDING , Antilock Brakes: refer to STANDARD PROCEDURE - ANTILOCK BRAKE SYSTEM BLEEDING | ||
| Disc Brakes | |||
| Service Specifications | Refer to SPECIFICATIONS | ||
| Torque | Base Brakes: refer to TORQUE SPECIFICATIONS , Antilock Brakes: refer to SPECIFICATIONS | ||
| Drum Brakes | |||
| Service Specifications | N/A | ||
| Torque | N/A | ||
| Charging | |||
| Generator | Refer to GENERATOR | ||
| Torque | Refer to TORQUE SPECIFICATIONS | ||
| Drive Belts | |||
| Adjustment | Serpentine belt used, not adjustable. | ||
| Drive Belt Routing | Refer to appropriate "Belt Routing" figure under REMOVAL . | ||
| Engine Cooling | |||
| General Service Specifications | Refer to SPECIFICATIONS | ||
| Radiator Cap Pressure | 16 to 20 psi (110 to 138 kPa) | ||
| Thermostat R & I | Refer to REMOVAL | ||
| Water Pump R & I | Refer to REMOVAL | ||
| Engine Mechanical | |||
| 3.6L | |||
| Compression | Compression should not be less than 689 kPa (100 psi) and not vary more than 25 percent from cylinder to cylinder. | ||
| Oil pressure | Refer OIL PRESSURE table under ENGINE SPECIFICATIONS . | ||
| Overhaul | Refer to ENGINE SPECIFICATIONS | ||
| Torque | Refer to TORQUE SPECIFICATIONS | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE/FLUIDS tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flywheel/Flex Plate/Drive Plate Torque | |||
| 3.6L | 70 ft. lbs. (95 N.m) Do not reuse these fasteners. If removed, a NEW fastener must be installed and tightened to specifications. |
||
| Fuel System | |||
| Pressure Specification | 400 kPa ± 34 kPa (58 psi ± 5 psi) | ||
| Fuel Pressure Test Procedure | CHECKING THE FUEL DELIVERY SYSTEM (HARD START) | ||
| Fuel Filter Location | Fuel filter is part of fuel pump module | ||
| Fuel Filter R & I | Gas: Refer to MODULE, FUEL PUMP | ||
| Ignition | |||
| Firing Order & Cylinder Identification | Refer to FIRING ORDER & CYLINDER IDENTIFICATION | ||
| Ignition Wires (Resistance) | Coil On Plug | ||
| Ignition Wires (Routing) | Coil On Plug | ||
| Spark Plug | |||
| 3.6L | |||
| Type | RER8ZWYCB4 | ||
| Gap | .043 in. (1.1 mm) | ||
| Torque | 14 ft. lbs. (18 N.m). | ||
| Starting | |||
| Starter | Refer to STARTER MOTOR | ||
| Torque | Refer to TORQUE | ||
| Wheel Alignment | |||
| Adjustment Specifications | Refer to WHEEL ALIGNMENT | ||
| Torque | Refer to SPECIFICATIONS | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 145 ft. lbs. (197 N.m) | ||